+ Reply to Thread
Results 1 to 15 of 15
  1. Senior Member
    Join Date
    May 2017
    Location
    Southeast
    Posts
    102
    #1

    Default I can't ping between Routers in the same LAN....

    packet.jpg

    So I have a packet tracer lab I'm working on and I can only ping between the routers on each side of my switches, not across. All four routers are on the same network. There are 4 switches setup in between the 4 routers.

    R1 can ping R2 vice versa, R3 can ping R4 vice versa.

    Here is the config for each router:

    R1#show int f0/0
    FastEthernet0/0 is up, line protocol is up (connected)
    Hardware is Lance, address is 0007.ec1a.d401 (bia 0007.ec1a.d401)
    Internet address is 150.101.45.1/29
    MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    Encapsulation ARPA, loopback not set
    ARP type: ARPA, ARP Timeout 04:00:00,
    Last input 00:00:08, output 00:00:05, output hang never
    Last clearing of "show interface" counters never
    Input queue: 0/75/0 (size/max/drops); Total output drops: 0
    Queueing strategy: fifo
    Output queue :0/40 (size/max)
    5 minute input rate 0 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    9 packets input, 1152 bytes, 0 no buffer
    Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 input packets with dribble condition detected
    9 packets output, 1152 bytes, 0 underruns
    0 output errors, 0 collisions, 2 interface resets
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier
    0 output buffer failures, 0 output buffers swapped out





    R2#sho int f0/0
    FastEthernet0/0 is up, line protocol is up (connected)
    Hardware is Lance, address is 0001.c9a1.d601 (bia 0001.c9a1.d601)
    Internet address is 150.101.45.2/29
    MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    Encapsulation ARPA, loopback not set
    ARP type: ARPA, ARP Timeout 04:00:00,
    Last input 00:00:08, output 00:00:05, output hang never
    Last clearing of "show interface" counters never
    Input queue: 0/75/0 (size/max/drops); Total output drops: 0
    Queueing strategy: fifo
    Output queue :0/40 (size/max)
    5 minute input rate 0 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    9 packets input, 1152 bytes, 0 no buffer
    Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 input packets with dribble condition detected
    9 packets output, 1152 bytes, 0 underruns
    0 output errors, 0 collisions, 2 interface resets
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier
    0 output buffer failures, 0 output buffers swapped out



    R3#sho int f0/0
    FastEthernet0/0 is up, line protocol is up (connected)
    Hardware is Lance, address is 0001.42ad.5a01 (bia 0001.42ad.5a01)
    Internet address is 150.101.45.3/29
    MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    Encapsulation ARPA, loopback not set
    ARP type: ARPA, ARP Timeout 04:00:00,
    Last input 00:00:08, output 00:00:05, output hang never
    Last clearing of "show interface" counters never
    Input queue: 0/75/0 (size/max/drops); Total output drops: 0
    Queueing strategy: fifo
    Output queue :0/40 (size/max)
    5 minute input rate 0 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    28 packets input, 3584 bytes, 0 no buffer
    Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 input packets with dribble condition detected
    29 packets output, 3712 bytes, 0 underruns
    0 output errors, 0 collisions, 1 interface resets
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier
    0 output buffer failures, 0 output buffers swapped out



    R4#sho int f0/0
    FastEthernet0/0 is up, line protocol is up (connected)
    Hardware is Lance, address is 0060.47ad.7501 (bia 0060.47ad.7501)
    Internet address is 150.101.45.4/29
    MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    Encapsulation ARPA, loopback not set
    ARP type: ARPA, ARP Timeout 04:00:00,
    Last input 00:00:08, output 00:00:05, output hang never
    Last clearing of "show interface" counters never
    Input queue: 0/75/0 (size/max/drops); Total output drops: 0
    Queueing strategy: fifo
    Output queue :0/40 (size/max)
    5 minute input rate 0 bits/sec, 0 packets/sec
    5 minute output rate 0 bits/sec, 0 packets/sec
    29 packets input, 3712 bytes, 0 no buffer
    Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
    0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
    0 input packets with dribble condition detected
    28 packets output, 3584 bytes, 0 underruns
    0 output errors, 0 collisions, 2 interface resets
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier
    0 output buffer failures, 0 output buffers swapped out
    Last edited by labscloud; 07-26-2017 at 04:55 PM.
    Reply With Quote Quote  

  2. SS -->
  3. Senior Member
    Join Date
    Dec 2007
    Location
    Grand Rapids, Michigan
    Posts
    1,872

    Certifications
    Network+ : A+ : Security+ : eJPT : Life+
    #2
    Sometimes packet tracer won't work even when things are set up correctly. Try doing a whole new lab and see what happens.
    Booya!!
    ------------------------------------------------------------------------------------------
    WIP : | CISSP [2018] | CISA [2018] | CAPM [2018] | eCPPT [2018] | CRISC [2019] | TORFL (TRKI) B1 | Learning: | Russian | Farsi |
    *****You can fail a test a bunch of times but what matters is that if you fail to give up or not*****
    Reply With Quote Quote  

  4. Senior Member
    Join Date
    Dec 2013
    Location
    USA
    Posts
    192

    Certifications
    CCNA R&S, CCNA Security, A+/N+/S+/P+/L+
    #3
    Can you post the running config for each router?
    Reply With Quote Quote  

  5. No longer active.
    Join Date
    Jul 2016
    Posts
    413
    #4
    ... or better still, make the CPT file available via a file share. e.g Dropbox.

    The Red Lights come to my attention...
    No longer an active member
    Reply With Quote Quote  

  6. Senior Member
    Join Date
    May 2017
    Location
    Southeast
    Posts
    102
    #5
    I'm not pinging out those interfaces though, I'm only pinging from the inside routers across the switches, not the serial link or going outwards. I'll add a dropbox file.
    Reply With Quote Quote  

  7. Senior Member
    Join Date
    May 2017
    Location
    Southeast
    Posts
    102
    #6
    Reply With Quote Quote  

  8. No longer active.
    Join Date
    Jul 2016
    Posts
    413
    #7
    Set SW3 FA0/24 and SW4 FA0/24 to VLAN150.
    No longer an active member
    Reply With Quote Quote  

  9. Senior Member CryptoQue's Avatar
    Join Date
    May 2017
    Location
    US
    Posts
    192

    Certifications
    MBA, BSIT, PMP, CISSP, CCNP, CCDP, CCNA, CCDA, CCENT, NET+, SEC+
    #8
    Can you provide what you have configured on switches 1-4 to eliminate layer 2 being the root cause of your issue?
    Reply With Quote Quote  

  10. Senior Member
    Join Date
    May 2017
    Location
    Southeast
    Posts
    102
    #9
    I got it guys! I didn't have the F0/24 ports on SW3 & SW4 configured as access ports with access to vlan 150.

    So I added:

    #switchport mode access
    #switchport access vlan 150

    I just assumed it was a L3 issue and not L2.

    That did the trick on both switches!
    Last edited by labscloud; 07-26-2017 at 07:10 PM.
    Reply With Quote Quote  

  11. Senior Member CryptoQue's Avatar
    Join Date
    May 2017
    Location
    US
    Posts
    192

    Certifications
    MBA, BSIT, PMP, CISSP, CCNP, CCDP, CCNA, CCDA, CCENT, NET+, SEC+
    #10
    Glad you figured it out.
    Reply With Quote Quote  

  12. No longer active.
    Join Date
    Jul 2016
    Posts
    413
    #11
    Thanks for posting the CPT file. I enjoyed the diagnostic challenge: It looks as if we both got there at the same time.
    No longer an active member
    Reply With Quote Quote  

  13. Senior Member
    Join Date
    May 2017
    Location
    Southeast
    Posts
    102
    #12
    Thanks man, it only took 2 minutes after pulling up the switches running configs and I compared them to SW1&2 and BOOM, there it was!
    Reply With Quote Quote  

  14. Junior Member Registered Member
    Join Date
    Jul 2017
    Posts
    1
    #13

    Arrow WANT TO PASS A+ Cert 901 and 902 first try?!

    If you want to pass A+ Cert please Text me at 443-680-7474 (NO CALLS!!!!!) Please Text name and which version you would like.
    Reply With Quote Quote  

  15. Senior Member Mr.Robot255's Avatar
    Join Date
    Apr 2017
    Location
    Ireland
    Posts
    115

    Certifications
    A+, MTA 98-366 ,Net+,CCent
    #14
    yeah don't call that number
    Reply With Quote Quote  

  16. No longer active.
    Join Date
    Jul 2016
    Posts
    413
    #15
    If you're wise, you won't text it either!
    No longer an active member
    Reply With Quote Quote  

+ Reply to Thread

Social Networking & Bookmarks