+ Reply to Thread
Page 2 of 2 First 12
Results 26 to 30 of 30
  1. Senior Member
    Join Date
    Jun 2007
    Posts
    921

    Certifications
    A+, SEC +, CCNA, 642-533, CCNP, C|EH
    #26
    When I try to go into VTP configuration mode this is all I get:


    catalyst_2900_als1(config)# vtp ?
    file Configure IFS filesystem file where VTP configuration is stored.




    I can't really change anything...
    Reply With Quote Quote  

  2. SS -->
  3. Senior Member
    Join Date
    Jun 2007
    Posts
    921

    Certifications
    A+, SEC +, CCNA, 642-533, CCNP, C|EH
    #27
    OH SNAP!!!!


    On the 2924 series you have to go into the vlan database mode to configure VTP...


    Well i learned something today!!!
    Reply With Quote Quote  

  4. Went to the dark side.... Moderator networker050184's Avatar
    Join Date
    Jul 2007
    Posts
    11,643

    Certifications
    CCNA, CCNP, CCIP, JNCIA-JUNOS, JNCIS-SP, JNCIP-SP, MCA200
    #28
    Quote Originally Posted by liven
    OH SNAP!!!!


    On the 2924 series you have to go into the vlan database mode to configure VTP...


    Well i learned something today!!!
    This is why most people recommend 2950/60s. The commands structure of the 2900xl models are different. If these are the only switches you are using ensure you know the syntax for the exam as well.
    An expert is a man who has made all the mistakes which can be made.
    Reply With Quote Quote  

  5. Senior Member Netwurk's Avatar
    Join Date
    May 2005
    Location
    Philadelphia, PA
    Posts
    1,153

    Certifications
    CCNA, Network+, A+ (CCNP Progress: 1/3)
    #29
    The 2005 edition of the CCNA Command Quick Reference (by ciscopress) has a section that gives you all the CCNA level switch commands for the 1900, 2900, and 2950 models. It's very helpful when you have a variety of switches. And it can help you transition when you upgrade.

    VLAN database mode isn't being tested on anymore, but it still works on most of the newer switches. You get a warning if you try to use it, but it does work


    Sw3550#vlan database
    % Warning: It is recommended to configure VLAN from config mode,
    as VLAN database mode is being deprecated. Please consult user
    documentation for configuring VTP/VLAN in config mode.

    Reply With Quote Quote  

  6. Senior Member
    Join Date
    Jun 2007
    Posts
    921

    Certifications
    A+, SEC +, CCNA, 642-533, CCNP, C|EH
    #30
    Quote Originally Posted by Netwurk
    The 2005 edition of the CCNA Command Quick Reference (by ciscopress) has a section that gives you all the CCNA level switch commands for the 1900, 2900, and 2950 models. It's very helpful when you have a variety of switches. And it can help you transition when you upgrade.

    VLAN database mode isn't being tested on anymore, but it still works on most of the newer switches. You get a warning if you try to use it, but it does work


    Sw3550#vlan database
    % Warning: It is recommended to configure VLAN from config mode,
    as VLAN database mode is being deprecated. Please consult user
    documentation for configuring VTP/VLAN in config mode.


    Thanks!

    I realize vlan database is out of scope. I already have my CCNA, I am actually studying for CCNP, so I did a bad thing posting here.


    I was just trying to figure out what whas going on with this switch.

    Thanks guys for all of your help!!!
    Reply With Quote Quote  

+ Reply to Thread
Page 2 of 2 First 12

Social Networking & Bookmarks