+ Reply to Thread
Results 1 to 7 of 7

Thread: Aironet 1242AG

  1. Senior Member
    Join Date
    May 2007
    Location
    Fair Lawn, NJ
    Posts
    407

    Certifications
    CCNA, CCNP
    #1

    Default Aironet 1242AG

    I juts bought an Aironet 1242AG, I went and I reset the AP by pressing the mode button while plugging the power cable. I see that the AP has 10.0.0.1 default address. So, I went into my MAc and I setup my computer Ip as 10.0.0.10 with 255.255.255.0. When I try to ping I get the following:
    Request timeout for icmp_seq 0
    Request timeout for icmp_seq 1
    Request timeout for icmp_seq 2
    Request timeout for icmp_seq 3
    - I went into the router and I assigned an ip address of 10.0.0.1 just in case, but no luck. Can anybody help me out. I also try to access thru the web browser, still no good.
    Reply With Quote Quote  

  2. SS -->
  3. was here.
    Join Date
    Apr 2008
    Posts
    4,504
    #2
    Post a boot log and the configuration from the AP.
    Reply With Quote Quote  

  4. Senior Member
    Join Date
    May 2007
    Location
    Fair Lawn, NJ
    Posts
    407

    Certifications
    CCNA, CCNP
    #3
    Xmodem file system is available.
    flashfs[0]: 146 files, 7 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 15998976
    flashfs[0]: Bytes used: 5179392
    flashfs[0]: Bytes available: 10819584
    flashfs[0]: flashfs fsck took 27 seconds.
    Base ethernet MAC Address: 00:4f:2a:2c:c9:a6
    Initializing ethernet port 0...
    Reset ethernet port 0...
    Reset done!
    ethernet link up, 100 mbps, full-duplex
    Ethernet port 0 initialized: link is up
    Loading "flash:/c1240-k9w7-mx.123-11.JA4/c1240-k9w7-mx.123-11.JA4"...###########
    ################################################## ##############################
    ################################################## ##############################
    ################################################## ##############################
    ################################################## ##############################
    ################################################## ##############################
    ###

    File "flash:/c1240-k9w7-mx.123-11.JA4/c1240-k9w7-mx.123-11.JA4" uncompressed and
    installed, entry point: 0x3000
    executing...

    Restricted Rights Legend

    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec..

    cisco Systems, Inc.
    170 West Tasman Drive
    San Jose, California 95134-1706



    Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.3(11)JA4, RELEASE
    SOFTWARE (fc1)
    Technical Support: Cisco - Shortcut
    Copyright (c) 1986-2007 by Cisco Systems, Inc.
    Compiled Tue 17-Jul-07 19:29 by hqluong
    Image text-base: 0x00003000, data-base: 0x007AE540

    Initializing flashfs...

    flashfs[1]: 146 files, 7 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 15998976
    flashfs[1]: Bytes used: 5179392
    flashfs[1]: Bytes available: 10819584
    flashfs[1]: flashfs fsck took 4 seconds.
    flashfs[1]: Initialization complete....done Initializing flashfs.

    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.

    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    Export Compliance Product Report Application

    If you require further assistance please contact us by sending email to
    export@cisco.com.

    cisco AIR-AP1242AG-A-K9 (PowerPCElvis) processor (revision A0) with 24566K/81
    92K bytes of memory.
    Processor board ID FRF345645B1ZR
    PowerPCElvis CPU at 266Mhz, revision number 0x0950
    Last reset from power-on
    1 FastEthernet interface
    2 802.11 Radio(s)

    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:4f:2a:2c:c9:a6
    Part Number : 68-8897-08
    PCA Assembly Number : 678-54678-04
    PCA Revision Number : A0
    PCB Serial Number : FOC43566788l3
    Top Assembly Part Number : 700-45665-03
    Top Assembly Serial Number : FTD3895488Ft
    Top Revision Number : A0
    Product/Model Number : AIR-AP1242AG-A-K9



    Press RETURN to get started!


    *Mar 1 00:00:05.587: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self t
    est passed
    *Mar 1 00:00:07.053: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self
    test passed on interface Dot11Radio 0
    *Mar 1 00:00:07.405: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to r
    eset
    *Mar 1 00:00:08.608: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self
    test passed on interface Dot11Radio 1
    *Mar 1 00:00:10.735: %SYS-6-LOGGERSTART: Logger process started
    *Mar 1 00:00:10.736: %LI
    ap>
    ap>NK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar 1 00:00:11.736: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
    et0, changed state to down
    *Mar 1 00:00:19.646: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
    et0, changed state to up
    *Mar 1 00:00:56.812: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to a
    dministratively down
    *Mar 1 00:00:56.814: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to a
    dministratively down
    *Mar 1 00:00:56.859: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power s
    ource
    *Mar 1 00:00:56.884: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1240 Software (C1240-K9W7-M), Version 12.3(11)JA4, RELEASE
    SOFTWARE (fc1)
    Technical Support: Cisco - Shortcut
    Copyright (c) 1986-2007 by Cisco Systems, Inc.
    Compiled Tue 17-Jul-07 19:29 by hqluong
    *Mar 1 00:00:56.885: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a c
    old start
    *Mar 1 00:00:57.812: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
    1, changed state to down
    *Mar 1 00:00:57.814: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
    0, changed state to down
    *Mar 1 00:00:57.844: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
    ged state to up
    Reply With Quote Quote  

  5. Senior Member
    Join Date
    May 2007
    Location
    Fair Lawn, NJ
    Posts
    407

    Certifications
    CCNA, CCNP
    #4
    ap(config-if)#do sh run
    Building configuration...

    Current configuration : 1563 bytes
    !
    version 12.3
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    !
    hostname ap
    !
    enable secret 5 $1$8W/A$j5OUyUqKeBF4QT0T6Ek2L1
    !
    ip subnet-zero
    !
    !
    no aaa new-model
    power inline negotiation prestandard source
    !
    !
    username Cisco password 7 106D000A0618
    !
    bridge irb
    !
    !
    interface Dot11Radio0
    no ip address
    no ip route-cache
    shutdown
    speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0
    54.0
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    !
    interface Dot11Radio1
    no ip address
    no ip route-cache
    shutdown
    dfs band 3 block
    speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0
    channel dfs
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    !
    interface FastEthernet0
    ip address 10.0.0.1 255.255.255.0
    no ip route-cache
    duplex auto
    speed auto
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    !
    interface BVI1
    ip address dhcp client-id FastEthernet0
    no ip route-cache
    !
    ip http server
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779...onfig/help/eag

    !
    control-plane
    !
    bridge 1 route ip
    !
    !
    !
    line con 0
    line vty 0 4
    login local
    !
    end

    ap(config-if)#
    Reply With Quote Quote  

  6. was here.
    Join Date
    Apr 2008
    Posts
    4,504
    #5
    Fa0 is part of BVI1 which is requesting a DHCP address using the MAC address of Fa0. You should give BVI1 a static IP or use whatever the DHCP server has assigned it. Fa0 shouldn't have any IP address if it is part of a bridge group.

    Run "sho ip int bri" to see what is the assigned IP address.
    Reply With Quote Quote  

  7. Senior Member
    Join Date
    May 2007
    Location
    Fair Lawn, NJ
    Posts
    407

    Certifications
    CCNA, CCNP
    #6
    Thanks, is working now.
    Reply With Quote Quote  

  8. was here.
    Join Date
    Apr 2008
    Posts
    4,504
    #7
    Quote Originally Posted by amb1s1 View Post
    Thanks, is working now.
    Good to hear.

    You should upgrade the firmware on your AP. Cisco lets you download the firmware for their APs with just a guest level account. The latest I believe is 12.4(21a)JA1 for an autonomous AP1242AG. Make sure you get the autonomous version and not the LWAPP version however.
    Reply With Quote Quote  

+ Reply to Thread

Social Networking & Bookmarks