+ Reply to Thread
Results 1 to 2 of 2
  1. Go ping yourself... phoeneous's Avatar
    Join Date
    Dec 2008
    Location
    Console.WriteLine("Yo");
    Posts
    2,316

    Certifications
    Pimp status
    #1

    Question SOLVED: Can't connect to standalone 1142

    First time setting up a standalone 1142, can't get any clients to connect to it. On an xp laptop, hangs at acquiring network address for about 20 seconds then fails then gets apipa address. Using vlan 40 for wifi traffic. Switchport is trunking and shows vlan 40. I'm able to ping the internet gateway's .40 subinterface from the ap and vice versa. AP is handling dhcp. AP should be using WPA2 psk. See scrubbed config below, any help is appreciated.

    1142#sh run
    Building configuration...
    Current configuration : 4534 bytes
    !
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    !
    hostname 1142
    !
    !
    no aaa new-model
    ip domain name company.com
    ip name-server 172.18.80.1
    no ip dhcp use vrf connected
    ip dhcp excluded-address 172.18.84.1 172.18.84.99
    ip dhcp excluded-address 172.18.84.201 172.18.84.255
    !
    ip dhcp pool ***COMPANY_WIFI***
    network 172.18.84.0 255.255.255.0
    default-router 172.18.84.1
    dns-server 172.18.80.1
    domain-name company.com
    !
    !
    login on-failure
    login on-success
    dot11 syslog
    !
    dot11 ssid TEST
    vlan 40
    authentication open
    authentication key-management wpa version 2
    mbssid guest-mode
    wpa-psk ascii 7 blahblahblah
    !
    !
    crypto pki trustpoint TP-self-signed-84115847
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-84115847
    revocation-check none
    rsakeypair TP-self-signed-84115847
    !
    !
    !
    !
    ip ssh version 2
    bridge irb
    !
    !
    interface Dot11Radio0
    no ip address
    no ip route-cache
    !
    encryption vlan 40 mode ciphers aes-ccm
    !
    ssid TEST
    !
    antenna gain 0
    mbssid
    station-role root
    bridge-group 1
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    !
    interface Dot11Radio0.40
    encapsulation dot1Q 40
    no ip route-cache
    bridge-group 40
    bridge-group 40 subscriber-loop-control
    bridge-group 40 block-unknown-source
    no bridge-group 40 source-learning
    no bridge-group 40 unicast-flooding
    bridge-group 40 spanning-disabled
    !
    interface Dot11Radio1
    no ip address
    no ip route-cache
    shutdown
    antenna gain 0
    dfs band 3 block
    channel dfs
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    !
    interface GigabitEthernet0
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    no keepalive
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    !
    interface GigabitEthernet0.40
    encapsulation dot1Q 40
    no ip route-cache
    bridge-group 40
    no bridge-group 40 source-learning
    bridge-group 40 spanning-disabled
    !
    interface BVI1
    ip address 172.18.84.10 255.255.255.0
    no ip route-cache
    !
    ip default-gateway 172.18.84.1
    no ip http server
    ip http authentication local
    ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779...onfig/help/eag
    bridge 1 route ip
    !
    !
    !
    line con 0
    exec-timeout 0 0
    privilege level 15
    logging synchronous
    login local
    line vty 0 4
    privilege level 15
    logging synchronous
    login local
    transport input telnet ssh
    line vty 5 15
    privilege level 15
    logging synchronous
    login local
    transport input telnet ssh
    !
    end
    1142#
    Last edited by phoeneous; 12-01-2011 at 07:44 PM. Reason: solved
    Reply With Quote Quote  

  2. Go ping yourself... phoeneous's Avatar
    Join Date
    Dec 2008
    Location
    Console.WriteLine("Yo");
    Posts
    2,316

    Certifications
    Pimp status
    #2

    Default Solved

    Just figured it out, forgot to add encap dot1q 40 native to all my subinterfaces...
    Reply With Quote Quote  

+ Reply to Thread

Social Networking & Bookmarks