+ Reply to Thread
Results 1 to 1 of 1

Thread: cisco e&m

  1. A29
    A29 is offline
    Junior Member
    Join Date
    Oct 2009
    Posts
    1
    #1

    Default cisco e&m

    Hi,
    I have cisco 2811 (hostname Cisco_s) Version 12.4(15)T1 with E&M Voice daughter card (2 port) VIC2-2E/M in my office. Cisco_s connected to PBX.
    and cisco 2811 (hostname Cisco_p) Version 12.4(22)T with E&M Voice daughter card (2 port) VIC3-2E/M in other office. Cisco_p connected to terminals.
    PBX- ---- Cisco_s ----Ethernet --- Cisco_p ----terminal
    Cisco_s
    Code:
    Sh run
    voice-port 0/0/0
     auto-cut-through
     operation 4-wire
     type 5
     signal immediate
     compand-type a-law
     connection plar 2000
    !
    voice-port 0/0/1
     auto-cut-through
     operation 4-wire
     type 5
     signal immediate
     compand-type a-law
     connection plar 2001
    !
    dial-peer voice 1 pots
     destination-pattern 1000
     port 0/0/0
    !
    dial-peer voice 2 pots
     destination-pattern 1001
     port 0/0/1
    !
    dial-peer voice 3 voip
     destination-pattern 2000
     session target ipv4:192.192.192.192
     codec g711alaw
    !
    dial-peer voice 4 voip
     destination-pattern 2001
     session target ipv4:192.192.192.192
     codec g711alaw
    Thanks for any input.
    Cisco_p
    Code:
    Sh run
    voice-port 0/0/0
     auto-cut-through
     operation 4-wire
     type 5
     signal immediate
     compand-type a-law
     connection plar 1000
    !
    voice-port 0/0/1
     auto-cut-through
     operation 4-wire
     type 5
     signal immediate
     compand-type a-law
     connection plar 1001
    !
    ccm-manager fax protocol cisco
    !
    mgcp fax t38 ecm
    !
    dial-peer voice 1 pots
     destination-pattern 2000
     port 0/0/0
    !
    dial-peer voice 2 pots
     destination-pattern 2001
     port 0/0/1
    !
    dial-peer voice 3 voip
     destination-pattern 1000
     voice-class permanent 10
     session target ipv4:192.192.193.193
     codec g711alaw
    !
    dial-peer voice 4 voip
     destination-pattern 1001
     voice-class permanent 10
     session target ipv4:192.192.193.193
     codec g711alaw
    When the voice transfer goes, “ in status” and “out status” is seized in Cisco_p and Cisco_s
    Code:
    sh voice port sum (in  Cisco_p and Cisco_s)
                                              IN       OUT
    PORT           CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
    ============== == ============ ===== ==== ======== ======== ==
    0/0/0          --  e&m-imd     up    up   seized   seized   y
    0/0/1          --  e&m-imd     up    up   seized   seized   y
    
    PWR FAILOVER PORT        PSTN FAILOVER PORT
    =================        ==================
    In a case Cisco_p or Cisco_s rebooted, after reboot the voice transfer does not go. “ in status” and “out status” is idle in Cisco_p and Cisco_s.
    Shutdown/no shutdown - not renew a voice transfer. For voice transfer renewal it is necessary to pull out and insert simultaneously cables from ports e&m on both cisco.
    It creates many problems. Tried put signal delay-dial or wink-start ports were able idle and the voice transfer was not. What it is necessary to change in my config?
    Thanks for any input.
    Last edited by A29; 10-13-2009 at 09:08 AM.
    Reply With Quote Quote  

+ Reply to Thread

Social Networking & Bookmarks