+ Reply to Thread
Results 1 to 2 of 2
  1. Junior Member
    Join Date
    May 2008
    Location
    Brooklyn,Newyork
    Posts
    12
    #1

    Default Problems of adding subscriber

    Hello everyone,
    I think I need help.It's a lab environment on ESXi.I am trying to install a subscriber and add it to the subscriber. A publisher is installed. IP is 192.168.1.86 and hostname is ccm8. The installing subscriber's IP is 192.168.1.87 and the hostname is ccm8sub. I did go to the publisher's CUCM admin -> System -> Servers to add a the subscriber.
    I got several similar messages (see the attached pictures) as I tried several times.

    I changed the admin and OS password of the publisher before. I found that only after I use the original password, the subscriber is authenticated through running the command ' show network cluster'. But the error message shows in pic 3

    Below are some message from the publisher:

    admin:show network cluster
    192.168.1.86 ccm8 Publisher authenticated
    192.168.1.87 ccm8sub Subscriber not authenticated - INITIATOR since Wed Jan 26 12:50:32 2011

    -----------------------------------------------------------------------------------------------------
    after I changed to the original password:

    admin:show network cluster
    192.168.1.86 ccm8 Publisher authenticated
    192.168.1.87 ccm8sub Subscriber authenticated using TCP since Wed Jan 26 13:17:54 2011

    -----------------------------------------------------------------------------------------------------

    admin:utils network ping 192.168.1.87
    PING 192.168.1.87 (192.168.1.87) 56(84) bytes of data.
    64 bytes from 192.168.1.87: icmp_seq=0 ttl=64 time=0.198 ms
    64 bytes from 192.168.1.87: icmp_seq=1 ttl=64 time=0.195 ms
    64 bytes from 192.168.1.87: icmp_seq=2 ttl=64 time=0.197 ms
    64 bytes from 192.168.1.87: icmp_seq=3 ttl=64 time=0.229 ms

    --- 192.168.1.87 ping statistics ---
    4 packets transmitted, 4 received, 0% packet loss, time 3005ms
    rtt min/avg/max/mdev = 0.195/0.204/0.229/0.022 ms, pipe 2

    -----------------------------------------------------------------------------------------------------


    admin:utils network ping ccm8
    PING ccm8 (192.168.1.86) 56(84) bytes of data.
    64 bytes from ccm8 (192.168.1.86): icmp_seq=0 ttl=64 time=0.032 ms
    64 bytes from ccm8 (192.168.1.86): icmp_seq=1 ttl=64 time=0.032 ms
    64 bytes from ccm8 (192.168.1.86): icmp_seq=2 ttl=64 time=0.040 ms
    64 bytes from ccm8 (192.168.1.86): icmp_seq=3 ttl=64 time=0.029 ms

    --- ccm8 ping statistics ---
    4 packets transmitted, 4 received, 0% packet loss, time 3043ms
    rtt min/avg/max/mdev = 0.029/0.033/0.040/0.005 ms, pipe 2

    -----------------------------------------------------------------------------------------------------

    admin:utils network ping ccm8sub
    PING ccm8sub (192.168.1.87) 56(84) bytes of data.
    64 bytes from ccm8sub (192.168.1.87): icmp_seq=0 ttl=64 time=1.21 ms
    64 bytes from ccm8sub (192.168.1.87): icmp_seq=1 ttl=64 time=0.189 ms
    64 bytes from ccm8sub (192.168.1.87): icmp_seq=2 ttl=64 time=0.198 ms
    64 bytes from ccm8sub (192.168.1.87): icmp_seq=3 ttl=64 time=0.204 ms

    --- ccm8sub ping statistics ---
    4 packets transmitted, 4 received, 0% packet loss, time 3146ms
    rtt min/avg/max/mdev = 0.189/0.451/1.216/0.442 ms, pipe 2

    -----------------------------------------------------------------------------------------------------
    admin:show network eth0 detail
    Ethernet 0
    DHCP : disabled Status : up
    IP Address : 192.168.1.86 IP Mask : 255.255.255.000
    Link Detected: yes Mode : Auto enabled, Full, 1000 Mbits/s
    Duplicate IP : no
    Queue Length : 1000 MTU : 1500
    MAC Address : 00:0c:29:47:d9:a2
    RX stats:
    bytes : 247288456 packets : 2007605 errors : 0
    dropped : 0 overrun : 0 mcast : 0
    TX stats:
    bytes : 344836027 packets : 674703 errors : 0
    dropped : 0 carrier : 0 colsns : 0

    DNS
    Not configured.
    Gateway : 192.168.1.168 on Ethernet 0
    Attached Images Attached Images
    Reply With Quote Quote  

  2. Junior Member
    Join Date
    May 2008
    Location
    Brooklyn,Newyork
    Posts
    12
    #2
    Wow, it's almost a year I posted this.. haha, I just have the same problem and I solved it. I think I need to go to the System --> CUCM to add my subscriber as well. I probably didn't that I have to do that before I posted it. To sum up, I have to go to system - CUCM and System -server to add the subscriber.
    The case closed..
    Reply With Quote Quote  

+ Reply to Thread

Social Networking & Bookmarks